Engine Accessories

Name
Set Descending Direction

Grid List

80 per page

12 Item(s)

  1. 28mm ブローオフバルブキャンセラー S13/180sx Blow Off Valve return blocker

    28mm ブローオフバルブキャンセラー

    ¥1,960

    The GKTECH Blow Off Valve return blocker fits all S13, S14 and S15's, R33 (GTS-T) and R34's (GT-T) and is to be used on the intake pipe when the standard blow off valve is removed. If the hole left from removing the blow off valve isn't removed, air will get sucked into the intake after the air flow meter and the car will run very rough.

    - 1 piece billet aluminium construction
    - Direct replacement<br>- 28mm's in diameter

  2. 3"76mm タービンインレットアダプター T25/T28/GT2871r etc. 3"76mm タービンインレットアダプター T25/T28/GT2871r etc.

    3"76mm タービンインレットアダプター T25/T28/GT2871r etc.

    ¥4,800
    The GKTECH billet aluminium turbo intake snout has a 3" inlet and 2.5" outlet to suit most 2 bolt turbos including T25, T25g, T28, GT2871r, GT3071r (with 2 bolt front housing) etc. etc.
  3. CA18/SR20/KA24 ポリウレタン強化エンジンマウント (Pair) CA18/SR20/KA24 ポリウレタン強化エンジンマウント (Pair)

    CA18/SR20/KA24 ポリウレタン強化エンジンマウント (Pair)

    ¥9,880

    The GKTECH CA18/SR20 Polyurethane engine mounts are a direct replacement of the standard item and helps reduce engine movement and get power to the ground. Particularly useful in a drift car where the car is off and on the throttle although all forms of motorsport will see an improvement in feel of the car but without the drastic increase in vibrations that the solid mounts see. Our multi piece construction makes these differing to most Polyurethane engine mounts in that these don't just run a bolt all the way through a block of Polyurethane rather the 2 sides are separate and join by the Polyurethane.

  4. CA18/SR20/KA24 リジットエンジンマウント (Pair) CA18/SR20/KA24 リジットエンジンマウント (Pair)

    CA18/SR20/KA24 リジットエンジンマウント (Pair)

    ¥6,415

    The GKTECH CA18/SR20 solid engine mounts are a direct replacement of the standard item and helps reduce engine movement and get power to the ground. Particularly useful in a drift car where the car is off and on the throttle.

  5. RB/VG カップリングファンアダプター RB/VG カップリングファンアダプター

    RB/VG カップリングファンアダプター

    ¥1,800

    If you want to use one of our super dooper awesome clutch fans on your RB/VG series motor then you will need to use one of these billet aluminium adapters. The PCD, bore size and the offset all differ from the SR to the RB/VG but this adapter is hub centric and leaves only a 2mm offset variance when compared to your standard RB/VG clutch fan with the standard clutch. Ie. it means that the fan will sit 2mm's closer to the radiator when using our clutch fan with this adapter.

    Our clutch fan is a proven performer with over 800 satisfied customers using these on the SR20's and compared to the RB/VG clutch fan you will see an increase in air flow of around 40% which is easily noticable the second that you install the fan.

  6. S13/180sx SR20 T28 変換アダプターセット S13/180sx SR20 T28 変換アダプターセット

    S13/180sx SR20 T28 変換アダプターセット

    ¥5,940
    The GKTECH aluminium turbo adapters allow the use of the standard S13/180sx SR20 turbo snout/intake and hot pipe snout with any GT28 turbo. This makes installing a T28 on a redtop SR20 a piece of cake and saves the headache of having to get custom pipe work made up. Will suit all T28, GT2871r, GT3071r etc. (with 2 bolt front housing)
  7. S13/180sx SR20DET 偏芯スロットルホイール S13/180sx SR20DET Eccentric throttle wheel

    S13/180sx SR20DET 偏芯スロットルホイール

    ¥6,480

    The S13/180sx SR20DET eccentric (ie. off-center) throttle wheel makes the travel of the throttle cable down low in the rev range longer and gives you more control, and makes the travel up high shorter for instant throttle response. Great for drift
    or even general street use. Seriously, one of the best cheap mods money can buy.

  8. SR/KA/RB/VG ハイフローファン - 60% more air flow S13/S14/S15 Replacement Engine fan - 60% more air flow

    SR/KA/RB/VG ハイフローファン - 60% more air flow

    ¥9,400

    The GKTECH high performance engine fan has been designed and engineered in Australia with the intention of pulling more air than the factory item.

    When tested on a dyno the GKTECH high performance fan took less than half the time to cool down from 90 degrees to operating temperature (good for next time you're on the start line at the track).

    Super easy to install, simply remove your factory fan (4 bolts) and install the new fan, it is a direct replacement clutch fan to suit SR, KA, RB, VG engines

  9. SR20 クーラントネックスペーサー(水温センサ取付可) SR20 coolant neck spacer

    SR20 クーラントネックスペーサー(水温センサ取付可)

    ¥4,180

    Want to install an aftermarket coolant temp sensor but don't want to cut into your radiator hose? Me either! Instead of doing that simply unbolt your factory coolant neck and install this spacer in between the neck and the head.
    The spacer has the provision for a 1/8 NPT provision or alternatively if used in conjunction with a barbed fitting this spacer could be used as the source for a coolant breather tank.

  10. SR20 ロッカーアームストッパー / RAS SR20 Rocker Arm Stoppers / RAS

    SR20 ロッカーアームストッパー / RAS

    ¥4,716

    Used for extra reliability at high RPM in SR engines. These rocker arm stoppers hold the lash adjuster side of the rocker arm at a fixed clearance, preventing extra movement at high RPM.

  11. V2 S14/S15 偏芯スロットルホイール V2 S14a/S15 Eccentric throttle wheel

    V2 S14/S15 偏芯スロットルホイール

    ¥5,800

    The S14a/S15 eccentric (ie. off-center) throttle wheel makes the travel of the throttle cable down low in the rev range longer and gives you more control, and makes the travel up high shorter for instant throttle response. Great for drift
    or even general street use. Seriously, one of the best cheap mods money can buy.

    - Light weight T6-6061 billet aluminium construction
    - Direct bolt on replacement of the standard throttle wheel
    - Confirmed fitment for VCT SR20's fitted in S14a's and S15's. This wheel will NOT fit non VCT motors or Series 1 S14's.

  12. タービン インタークーラーアウトレットアダプター タービン インタークーラーアウトレットアダプター

    タービン インタークーラーアウトレットアダプター

    ¥3,880

    The GKTECH billet aluminium turbo to intercooler hotpipe snout is 2" and is a bolt on to most Nissan turbos including T25, T25g, T28, GT2871r, GT3071r (with 3 bolt front housing outlet). A great item if you're installing a different turbo on your car and want an easy way to get your intercooler piping to line up.

Name
Set Descending Direction

Grid List

80 per page

12 Item(s)